| Parameter | Value | Verification Method | |-----------|-------|----------------------| | Model | BJ42D15 26V10 | Label inspection | | Phase | 2 | Electrical continuity | | Step Angle | 1.8° ± 5% | Oscilloscope / encoder | | Number of Leads | 4 | Visual | | Rated Voltage | 26 V DC | Power supply test | | Rated Current per Phase | 1.0 A | Current probe | | Winding Resistance | 26 Ω ± 10% @ 20°C | 4-wire ohmmeter | | Winding Inductance | 28 mH ± 20% @ 1 kHz | LCR meter | | Holding Torque | 0.42 N·m (59.5 oz·in) | Torque sensor (at 1.0 A) | | Detent Torque | 0.022 N·m (3.1 oz·in) | Torque wrench method | | Rotor Inertia | 54 g·cm² (0.54 × 10⁻⁵ kg·m²) | Calculated from acceleration | | Mass | 0.35 kg (12.3 oz) | Precision scale | | Body Length | 39.5 mm (excluding shaft) | Digital caliper | | Shaft Diameter | 5 mm | Micrometer | | Shaft Length | 24 mm | Caliper | | Max Radial Load | 28 N (5 mm from face) | Static load test | | Max Axial Load | 10 N (push/pull) | Force gauge | | Insulation Class | Class B (130°C) | Thermal camera | | Dielectric Strength | 500 VAC for 1 minute | Hipot tester | | Insulation Resistance | >100 MΩ @ 500 VDC | Megohmmeter |
Because it has a higher phase resistance (26Ω) compared to low voltage motors (1.5–5Ω), it draws only 1A at 26V. According to Ohm's Law: V = I × R → 26V = 1.0A × 26Ω.
Connecting one coil to the 1A and 1B terminals of your stepper driver, and the other coil to the 2A and 2B terminals, is standard. If the motor rotates in the wrong direction, simply reverse the connections for one of the coils (swap A and C or B and D ). bj42d15 26v10 stepper motor datasheet verified
Dynamic Characteristics: The characteristics related to the starting or rotation of a stepper motor primarily affect the operation... Oriental Motor India Which stepper motor is used in 3D printer? - Skysmotor
Continuous operation at rated 1.0 A per phase (both phases energized) in still air at 25°C ambient: | Parameter | Value | Verification Method |
To run the properly, you must set the stepper driver current (VREF) correctly to avoid overheating or skipping steps. Target Current: For common drivers like the A4988 or TMC2209: VREF formula: Assuming standard sense resistors on an A4988: Set your driver VREF to
The following parameters are based on a sample of three motors from a single production batch (lot #B42-2409). Batch-to-batch variations may exist, particularly in: If the motor rotates in the wrong direction,
Based on manufacturer data and verified community testing for the BJ42D15 series, the primary specifications are as follows: Specification BJ42D15-26V10 Type 2-Phase Bipolar Hybrid Stepper Step Angle 1.8∘1.8 raised to the composed with power (200 steps per revolution) Rated Current 0.84 A per phase Rated Voltage 26V (Optimized for 24V systems) Holding Torque 2.86 kg·cm (approx. 0.28 N·m) Dimensions 42 x 42 x 34 mm Shaft Diameter 5 mm (standard NEMA 17) Key Features
The is a specific NEMA 17 stepper motor frequently used in 3D printers, most notably the Creality Ender 3 series (often for the X, Y, or Z axes). Because these are custom-manufactured for specific brands, a standalone "official" datasheet is rarely released, but the verified technical specifications have been documented through manufacturer labels and community testing. Verified Specifications Specification Model Number BJ42D15-26V10 Step Angle 1.8° (200 steps per revolution) [10] Rated Current 0.84A [5.1, 5.7] Phase Voltage ~3.9V - 4.2V (Calculated based on resistance) Phase Resistance ~4.7 - 5.0 Ωcap omega Phase Inductance Holding Torque ~0.35 N·m (3.5 kg·cm) Frame Size NEMA 17 (42mm x 42mm) [11] Motor Height 34mm (Standard for "42-34" class motors) [3, 9] Shaft Diameter 5mm ("D" shape or Round depending on batch) [13] Key Configuration Notes
PREDICT BITCOIN